1RM calculator and load table

Enter the load and reps of one set to failure and see straight away the estimated 1RM, the heaviest load that can be lifted for a single rep, by 8 published equations, and the load for each number of reps, from 1 to 10. Free, no sign-up.

Updated

Units

The weight lifted in the set.

To failure, in a single set.

Shown in the report for your client.

Result

Estimated 1RM
Across the 8 equations

To see the result, enter: load and reps.

Are you a personal trainer? In MyFitnessClient, assessments keep your client's 1RM on the bench press, squat and deadlift, tested or estimated, and show the change from one assessment to the next.

Create a free accountFind a professional

In short

This calculator estimates the 1RM, the heaviest load that can be lifted for one rep, from one set to failure, by 8 published equations, and gives the load for 1 to 10 reps by the same equation. On the bench press, in a study of 31 men who trained in a gym, the six equations studied, five of them in this calculator, had a standard error of 2.7 to 3.2 kg (Lacio and colleagues, 2010). But accuracy changes with the exercise: on the 45° leg press, every equation studied by Menêses and colleagues (2013) overestimated the 1RM by 6 to 15%. It does not work for sets of more than 12 reps, is more reliable up to 10 and does not replace a 1RM test.

How it's calculated

The 8 equations

Each equation estimates the 1RM from the load lifted (w, in kg or lb) and the reps done to failure in a single set (r). These are the 8 we checked in at least two peer-reviewed papers, with the author and year of each:

  • Epley (1985): 1RM = w × (1 + r ÷ 30)
  • Brzycki (1993): 1RM = w × 36 ÷ (37 − r)
  • Lander (1985): 1RM = 100 × w ÷ (101.3 − 2.67123 × r)
  • Lombardi (1989): 1RM = w × r^0.10
  • Mayhew et al. (1992): 1RM = 100 × w ÷ (52.2 + 41.9 × exp(−0.055 × r))
  • O'Conner, Simmons and O'Shea (1989): 1RM = w × (1 + 0.025 × r)
  • Wathen (1994): 1RM = 100 × w ÷ (48.8 + 53.8 × exp(−0.075 × r))
  • Baechle and Groves (2000): 1RM = w × (0.0375 × r + 0.978)

exp(x) is the number e, about 2.718, raised to the power x, and r^0.10 is r raised to the power 0.10. With 1 rep, the 1RM is the load itself, in every equation.

The load table

The load for each number of reps comes from the same equation, inverted: if the equation says 1RM = w × f(r), the load that brings failure at r reps is the 1RM divided by f(r). The table shows that load rounded to 2.5 kg, or to 5 lb when the load is entered in lb; the maths is done without rounding.

  • load for r reps = 1RM ÷ f(r)
  • % of 1RM = 100 ÷ f(r)

The table is calculated from the chosen equation, not copied from any published table.

How to measure

Do a single set to failure, with a load that allows up to 10 full reps, with the usual technique, and enter the load and the reps. Reynolds and colleagues (2006), with 70 adults on the bench press and leg press, concluded that no more than 10 reps should be used in linear equations, and the estimate from 5 reps was the most accurate. Count only the reps to failure: a set stopped early gives a 1RM below the real one.

Example

One set of 5 reps to failure with 100 kg on the bench press. By the Epley equation, the one the calculator shows first:

  • 1RM = 100 × (1 + 5 ÷ 30) = 116.7 kg
The 1RM by the 8 equations
Epley116.7 kg
Brzycki112.5 kg
Lander113.7 kg
Lombardi117.5 kg
Mayhew119.0 kg
O'Conner112.5 kg
Wathen116.6 kg
Baechle and Groves116.6 kg

The 8 equations give between 112.5 kg and 119.0 kg. To track someone's progress, always use the same one.

Estimated load to failure
Reps% of 1RMLoad
1100%116.7 kg
294%110 kg
391%105 kg
488%102.5 kg
586%100 kg
683%97.5 kg
781%95 kg
879%92.5 kg
977%90 kg
1075%87.5 kg

By the Epley equation, rounded to 2.5 kg.

More about the calculator